Uwe Hermann | A slightly paranoid Debian developer

As you may know there's a Google Summer of Code program again this year.

The deadline for student applications is April 9th at 19:00 UTC, so if you're a student and you want to work on a coreboot (open-source BIOS / PC firmware) or flashrom (open-source BIOS chip flasher) project, please apply in time.

The following coreboot/flashrom GSOC project ideas have been proposed so far (but you can also suggest your own ideas, of course):

• Infrastructure for automatic code checking
• TianoCore on coreboot
• coreboot port to Marvell ARM SOCs with PCIe
• coreboot port to AMD 800 series chipsets
• coreboot mass-porting to AMD 780 series mainboards
• coreboot panic room
• coreboot cheap testing rig
• coreboot GeodeLX port from v3 to v4
• Drivers for libpayload
• Board config infrastructure
• Refactor AMD code
• Payload infrastructure
• flashrom: Multiple GUIs for flashrom
• flashrom: Recovery of dead boards and onboard flash updates
• flashrom: SPI bitbanging hardware support
• flashrom: Generic flashrom infrastructure improvements
• flashrom: Laptop support

See this wiki page for why and how to apply for a coreboot/flashrom project.

If you ever wanted to support an open-source project but you are not a programmer, here's one (of many possible) ways to help:

The Miro project (Internet TV / Video and Audio Podcast application for Linux, Windows, and Mac OS X) is seeking for pledges/donations that will be used to add subtitles support in Miro.

To quote from the announcement:

We’re hoping to build real subtitle support into Miro in the next couple months, but we need your help! So we’ve started a Kickstarter project to raise $1,000 to develop this feature for Miro on all three platforms: Windows, Mac, and Linux. Can you pledge to help make it happen? One of the great things about the Kickstarter model is that unless we can reach $1,000, your pledge won’t be charged.
[...]
(if you live in the United States, donations are tax deductible — we are a 501c3 non-profit)

There are 11 days left to make a pledge.

Dear Lazyweb,

is there any Free Software utility for putting those nice logos/images on LightScribe CDs or DVDs? I'm considering buying such a CD/DVD burner, but only if there's open-source software to control the device. I guess burning CDs/DVDs should be no problem using wodim/cdrecord, but adding images as labels on the CD/DVD is likely not possible without special software.

I know about the LightScribe Linux software (which is binary-only and not open-source, it seems) and LaCie LightScribe Labeler for Linux (which only creates labels but does not write them to the CD/DVD, and is not open-source either, I think).

Anyone aware of a Free Software utility for this? Or at least a public specification/datasheet which could be used for creating one? I might even be willing to join development if datasheets are available.

Yes, just when you thought the spamming of Planet Debian with "Lenny released" blog posts had finally stopped, here comes another one :-)

Let me join the crowd by saying a great "thank you!" to all the people who made this release possible, especially so the release team who organized everything, as well as the thousands of contributors (in one form or another) who helped shape the new release!

Personally, I'm eager to try out the new Linux 2.6.28 kernel package in unstable now (which have been uploaded today or so, but haven't yet reached my mirror), since they contain mainline wireless drivers for my One A110 netbook, among many other things.

Also, in the next few days I'll probably re-install my NSLU2 ARM box using the latest Lenny installer, following the HOWTOs by Martin Michlmayr (I'll probably write about the experience later). This re-install is long overdue, as I'm currently running the box from an 1GB thumb drive, which works ok, but I'm slowly running out of space. So I'll re-install on a 4 GB (or bigger) thumb drive.

As I wrote quite a while ago, I set up a RAID5 with three
IDE disks at home, which I'm using as backup (yes, I know that
RAID != backup) and storage space.

A few days ago, the RAID was put to a real-life test for the first time, as one of the disks died. Here's what that looks like in dmesg:

raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
 --- rd:3 wd:3
 disk 0, o:1, dev:hda2
 disk 1, o:1, dev:hdg2
 disk 2, o:1, dev:hde2
[...]
hdg: dma_timer_expiry: dma status == 0x21
hdg: DMA timeout error
hdg: 4 bytes in FIFO
hdg: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hdg: dma_timer_expiry: dma status == 0x21
hdg: DMA timeout error
hdg: 252 bytes in FIFO
hdg: dma timeout error: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hdg: dma_timer_expiry: dma status == 0x21
hdg: DMA timeout error
hdg: 252 bytes in FIFO
hdg: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hdg: DMA disabled
ide3: reset: success
hdg: dma_timer_expiry: dma status == 0x21
hdg: DMA timeout error
hdg: 252 bytes in FIFO
hdg: dma timeout error: status=0x58 { DriveReady SeekComplete DataRequest }
ide: failed opcode was: unknown
hdg: DMA disabled
ide3: reset: success
hdg: status timeout: status=0x80 { Busy }
ide: failed opcode was: 0xea
hdg: drive not ready for command
hdg: lost interrupt
hdg: task_out_intr: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown
hdg: lost interrupt
hdg: task_out_intr: status=0x50 { DriveReady SeekComplete }
ide: failed opcode was: unknown

That's when I realized that something was horribly wrong.

Not long after that, these messages appeared in dmesg. As you can see the software-RAID automatically realized that a drive died and removed the faulty disk from the array. I did not lose any data, and the system did not freeze up; I could continue working as if nothing happened (as it should be).

 md: super_written gets error=-5, uptodate=0
 raid5: Disk failure on hdg2, disabling device.
 raid5: Operation continuing on 2 devices.
 RAID5 conf printout:
  --- rd:3 wd:2
  disk 0, o:1, dev:hda2
  disk 1, o:0, dev:hdg2
  disk 2, o:1, dev:hde2
 RAID5 conf printout:
  --- rd:3 wd:2
  disk 0, o:1, dev:hda2
  disk 2, o:1, dev:hde2

This is how you can check the current RAID status:

 $ cat /proc/mdstat
 Personalities : [raid6] [raid5] [raid4] 
 md1 : active raid5 hda2[0] hde2[2] hdg2[3](F)
       584107136 blocks level 5, 64k chunk, algorithm 2 [3/2] [U_U]

The "U_U" means two of the disks are OK, and one is faulty/removed. The desired state is "UUU", which means all three disks are OK.

The next steps are to replace the dead drive with a new one, but first you should know exactly which disk you need to remove (in my case: hda, hde, or hdg). If you remove the wrong one, you're screwed. The RAID will be dead and all your data will be lost (RAID5 can survive only one dead disk at a time).

The safest way (IMHO) to know which disk to remove is to write down the serial number of the disk, e.g. using smartctl, and then check the back side of each disk for the matching serial number.

 $ smartctl -i /dev/hda | grep Serial
 $ smartctl -i /dev/hde | grep Serial
 $ smartctl -i /dev/hdg | grep Serial

(ideally you should get the serial numbers before one of the disks dies)

Now power down the PC and remove the correct drive. Get a new drive which is at least as big as the one you removed. As this is software-RAID you have quite a lot of flexibility; the new drive doesn't have to be from the same vendor / series, it doesn't even have to be of the same type (e.g. I got a SATA disk instead of another IDE one).

Insert the drive into some other PC in order to partition it correctly (e.g. using fdisk or cfdisk). In my case I needed a 1 GB /boot partition for GRUB, and the rest of the drive is another partition of the type "Linux RAID auto", which the software-RAID will then recognize.

Then, put the drive into the RAID PC and power it up. After a successful boot (remember, 2 out of 3 disks in RAID5 are sufficient for a working system) you'll have to hook-up the new drive into the RAID:

 $ mdadm --manage /dev/md1 --add /dev/sda2
 mdadm: added /dev/sda2

My new SATA drive ended up being /dev/sda2, which I added using mdadm. The RAID immediately starts restoring/resyncing all data on that drive, which may take a while (2-3 hours, depends on the RAID size and some other factors). You can check the current progress with:

 $ cat /proc/mdstat 
 Personalities : [raid6] [raid5] [raid4] 
 md1 : active raid5 sda2[3] hda2[0] hde2[2]
       584107136 blocks level 5, 64k chunk, algorithm 2 [3/2] [U_U]
       [>....................]  recovery =  0.1% (473692/292053568) finish=92.3min speed=52632K/sec

As soon as this process is finished you'll see this in dmesg:

 md: md1: recovery done.
 RAID5 conf printout:
  --- rd:3 wd:3
  disk 0, o:1, dev:hda2
  disk 1, o:1, dev:sda2
  disk 2, o:1, dev:hde2

In /proc/mdstat you'll see "UUU" again, which means your RAID is fully functional and redundant (with three disks) again. Yay.

 $ cat /proc/mdstat
 Personalities : [raid6] [raid5] [raid4] 
 md1 : active raid5 sda2[1] hda2[0] hde2[2]
       584107136 blocks level 5, 64k chunk, algorithm 2 [3/3] [UUU]

Btw, another nice utility you might find useful is hddtemp, which can check the temperature of the drives. You should take care that they don't get too hot, especially so if the RAID runs 24/7.

 $ hddtemp /dev/hda
 dev/hda: SAMSUNG HD300LD: 38 °C
 $ hddtemp /dev/hde
 dev/hde: SAMSUNG HD300LD: 44 °C
 $ hddtemp /dev/sda
 dev/sda: SAMSUNG HD322HJ: 32 °C